1. Introducing the smashing new Team FIAT T-Shirt !! To order yours click here : Team FIAT T-Shirt

DIY - Linea / Punto Head Up Display (HUD)

Discussion in 'Do It Yourself' started by Viny, Feb 26, 2011.

  1. Italia-Linea

    Italia-Linea Staff Member Janitor

    Messages:
    2,123
    Pune
    it works on punto mjd emotion pk. either there is a problem with your unit or you are not selecting correct settings.
  2. Ashpalio

    Ashpalio Amatore

    Messages:
    128
    Bangalore
    Bangalore
    Grande Punto 1.3
    Thank you Cinju for the quick reply. I am relieved to know that ELM 327 works for the Punto. I tried my unit on 1.3 MJD and 1.2 Puntos and both the time it did not work, where as in i10 it immediately worked without any hassle. I did not try your method. I tried a few settings and it did not work. Today I will try this and will tel the results. I hope it works.. I have been trying this stuff since Palio era,
    Last edited: Apr 28, 2011
  3. gurjinder

    gurjinder Staff Member Janitor

    Messages:
    3,989
    Punjab
    Excellent. Can you confirm whether the following three gauges are present?

    1. Engine oil temperature
    2. Exhaust gas temperature.
    3. Turbo boost pressure/ Values from MAF/MAP.

    Gurjinder.
  4. Ashpalio

    Ashpalio Amatore

    Messages:
    128
    Bangalore
    Bangalore
    Grande Punto 1.3
    Will check and update Gurjinder
  5. Cinju

    Cinju Esperto

    Messages:
    1,333
    Trivandrum
    Gurjinder...given below are the parameters supported by the tool. But I am not getting all these parameters.

    Standard OBD-II parameters

    Fuel system status
    Calculated Load
    Engine Coolant Temperature
    Short Term Fuel Trim B1
    Long Term Fuel Trim B1
    Short Term Fuel Trim B2
    Long Term Fuel Trim B2
    Fuel Pressure
    Intake Manifold Pressure
    Engine RPM
    Vehicle Speed
    Timing advance
    Intake Air Temperature
    Air Flow Rate
    Absolute Throttle Position
    O2 Sensor B1S1
    O2 Sensor B1S2
    O2 Sensor B1S3
    O2 Sensor B1S4
    O2 Sensor B2S1
    O2 Sensor B2S2
    O2 Sensor B2S3
    O2 Sensor B2S4
    Time Since Engine Start
    Distance with MIL
    Fuel Rail Pressure Rel. To Manifold
    Fuel Rail Pressure
    O2 Sensor (L/WB) B1S1
    O2 Sensor (L/WB) B1S2
    O2 Sensor (L/WB) B1S3
    O2 Sensor (L/WB) B1S4
    O2 Sensor (L/WB) B2S1
    O2 Sensor (L/WB) B2S2
    O2 Sensor (L/WB) B2S3
    O2 Sensor (L/WB) B2S4
    Commanded EGR
    EGR Error
    Commanded Evaporative Purge
    Fuel Level Input
    Number Of Warm-ups Since DTCs Cleared
    Distance Since DTCs Cleared
    Evap System Vapor Pressure
    Barometric Pressure
    O2 Sensor (WB) B1S1
    O2 Sensor (WB) B1S2
    O2 Sensor (WB) B1S3
    O2 Sensor (WB) B1S4
    O2 Sensor (WB) B2S1
    O2 Sensor (WB) B2S2
    O2 Sensor (WB) B2S3
    O2 Sensor (WB) B2S4
    Catalyst Temperature B1S1
    Catalyst Temperature B2S1
    Catalyst Temperature B1S2
    Catalyst Temperature B2S2
    Control Module Voltage
    Absolute Load Value
    Commanded Equivalence Ratio
    Relative Throttle Position
    Ambient Air Temperature
    Absolute Throttle Position (B)
    Absolute Throttle Position (C)
    Accelerator Pedal Position (D)
    Accelerator Pedal Position (E)
    Accelerator Pedal Position (F)
    Commanded Throttle Actuator Control
    Time with MIL
    Time Since DTCs Cleared
    Ethanol Fuel Ratio


    Non-Standard parameters

    Average Fuel Economy
    Momentary Fuel Economy
    OBD Port Voltage
    Odometer (OBDScope internal)
    Trip meter (OBDScope internal)
    Location
    GPS speed
    Air-Fuel-Ratio (AFR)
    Engine power estimate
    Engine torque estimate
  6. Ashpalio

    Ashpalio Amatore

    Messages:
    128
    Bangalore
    Bangalore
    Grande Punto 1.3
    Hi Cinju,
    I tried the steps you suggested, unsuccessful. The unit is working fine on i10. Which application are you using?
  7. Viny

    Viny Esperto

    Messages:
    1,742
    :)
    Ashpalio: Kindly share screenshots of your device and the details of the product that you have got.
  8. Cinju

    Cinju Esperto

    Messages:
    1,333
    Trivandrum
    Ashpalio..it should probably work because the device seems to be working. As Viny had asked, kindly share the screenshots of your device, the application which you are using and is the OBD version 1.4 which you are using ??
  9. Ashpalio

    Ashpalio Amatore

    Messages:
    128
    Bangalore
    Bangalore
    Grande Punto 1.3
    Hi Cinju,

    The OBD unit is Bluetooth ELM 327 v1.4 OBD II scanner. The application I have used are Torque (Android), Scan master (Windows), Scantool (Windows - given along with the Scanner). I have tried the scanner on my 1.3 MJD and 1.2 FIRE Punto. Which
  10. Viny

    Viny Esperto

    Messages:
    1,742
    :)
    Ashpalio: Did you got your bluetooth paring done, followed by com port creation?

    -
    f0M7w.jpg

Share This Page